Network Computing Devices NCD-5988-2 Instrukcja Użytkownika Pobierz pdf

2101

21-8156 12-03 NCD-5988-2

INSTALLATION INSTRUCTIONS

Congratulations - your new Air Helper Springs are quality

products capable of improving the handling and comfort of your

vehicle. As with all products, proper installation is the key to

obtaining all of the benefits your kit is capable of delivering.

Please take a few minutes to read through the instructions to

identify the components and learn where and how they are used.

It is a good idea to start by comparing the parts in your kit with

the parts list below.

The heart of the air helper spring kit is, of course, the air

helper springs. Remember that the air helper springs must flex

and expand during operation, so be sure that there is enough

clearance to do so without rubbing against any other part of the

vehicle.

Be sure to take all applicable safety precautions during the

installation of the kit. The instructions listed in this brochure

and the illustrations all show the left, or driver’s side of the

vehicle. To install the right side assembly simply follow the same

procedures.

Your kit includes separate inflation valves and air lines for

each air helper spring. This will allow you to level your vehicle

from side to side as well as from front to back. If you would rather

have a single valve inflation system, your dealer can supply the

required "T" fitting.

IMPORTANT!

For your safety and to prevent possible damage to your

vehicle, do not exceed the maximum load recommended by the

vehicle manufacturer (GVWR). Although your Air Helper

Springs are rated at a maximum inflation pressure of 100 P.S.I.,

this pressure may allow you to carry too great a load on some

vehicles. Check your vehicle owner’s manual for maximum

loads listed for your vehicle.

When inflating your Air Helper Springs, add air pressure

in small quantities, checking pressure frequently during

inflation. The air spring requires much less air volume than

a tire and, therefore, inflates much quicker.

WARNING:

Do not inflate this assembly when it is unrestricted.

The assembly must be restricted by the suspension

or other adequate structure. Do not inflate beyond

100 P.S.I. Improper use or over inflation may cause

property damage or severe personal injury.

267C AIR SPRING 6781 2

UPPER BRACKET (RIGHT) 5157 1

UPPER BRACKET (LEFT) 5158 1

LOWER BRACKET 5159 2

AXLE STRAP 1163 2

HEAT SHIELD 1004 1

3/8" -16 x 1" HEX BOLT 4

3/8" -16" x 3" CARRIAGE BOLT 4

3/8" -16 FLANGED LOCK NUT 12

3/8" -16 x 3/4" HEX BOLT 2

1/4" -20 x 1" HEX BOLT 2

1/4" FLAT WASHER 4

3/8" LARGE FLAT WASHER 4

1/4" LOCK WASHER 2

1/4" HEX NUT 2

PUSH-TO-CONNECT

MALE AIR FITTING 3046 2

PUSH-TO-CONNECT

INFLATION VALVE 3032 2

5/16" FLAT WASHER 4

AIR LINE TUBING 1

NYLON TIE 6

THERMAL SLEEVE 2

PARTS LIST

1 2 3 4

Podsumowanie treści

Strona 1 - INSTALLATION INSTRUCTIONS

210121-8156 12-03 NCD-5988-2INSTALLATION INSTRUCTIONSCongratulations - your new Air Helper Springs are qualityproducts capable of improving the handli

Strona 2 - FIGURE "A"

NOTE: Both illustrations are of the left, or driversside, of the vehicle. Reverse any orientations whenassembling and installing the right, or passe

Strona 3 - STEP 2 - PRE-ASSEMBLE THE KIT

FIGURE "B" FIGURE "C"STEP 1 - PREPARE THE VEHICLERemove the positive battery cable. With the vehicle on a solid, level surface

Strona 4 - STEP 6 - CHECK THE AIR SYSTEM

NOTE:Once the air helper springs are installed, it is recommended that the vehicle not be lifted by the frame, as over-extension mayoccur, resulting i

Komentarze do niniejszej Instrukcji

Brak uwag

Network Computing Devices NCD-5988-2 Instrukcja Użytkownika

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Nie Network Computing Devices NCD-5988-2. Network Computing Devices NCD-5988-2 User's Manual Instrukcja obsługi

Podsumowanie treści

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Nie Network Computing Devices NCD-5988-2